The reasoning for using a commit handler is to ensure that all paths for
output changes are correctly handled. With the centralized modeset
infrastructure in place, we can move the logic there. This allows us to
be smarter and avoid extraneous arranges, output manager updates and
transaction commits.
The side-effect is a minor duplication for the special-case
request_state, but the shared path will be relied upon further in future
commits to justify this duplication.
Since output layout is destroyed when the wayland display is destroyed
we run into a destroy listener order problem: Either the display starts
destroying the outputs first, in which case we're good: The existing
handling will clean up. However, things go wrong if the display decides
to destroy the output layout first. In this case, sway will hold
invalid references to the output layout as part of each output so that
when it finally goes to destroy them, sway will dereference destroyed
output layout bits.
Ref: https://github.com/swaywm/sway/pull/6844#issuecomment-1843599513
Currently, when encountering a non-desktop display, sway offers the
output for leasing and returns without storing it in a sway specific
output type like `struct sway_output`. Additionally, running
`swaymsg -t get_outputs` doesn't show non-desktop outputs.
This commit stores the non-desktop outputs into a struct called
`sway_output_non_desktop`, and adds them to a list on `sway_root`
There was some unused code-paths for rendering surfaces with an
arbitrary rotation applied. This was imported from rootston.
Since we don't have plans to make use of this, remove it.
Instead of calling wlr_xdg_surface_for_each_popup and then
wlr_surface_for_each_surface, use the new for_each_popup_surface helper
introduced in [1] that does it in one go.
[1]: https://github.com/swaywm/wlroots/pull/2609
Instead of listening to both transform and scale events, we can listen
to the commit event and use the new wlr_output_event_commit struct to
decide what to do.
This de-duplicates some of the work we were doing twice when an output
was re-configured.
Depends on [1].
[1]: https://github.com/swaywm/wlroots/pull/2315
Previously, we called output_disable prior to wlr_output_commit. This
mutates Sway's output state before the output commit actually succeeds.
This results in Sway's state getting out-of-sync with wlroots'.
An alternative fix [1] was to revert the changes made by output_disable
in case of failure. This is a little complicated. Instead, this patch
makes it so Sway's internal state is never changed before a successful
wlr_output commit.
We had two output flags: enabled and configured. However enabled was set
prior to the output becoming enabled, and was used to prevent the output
event handlers (specifically, the mode handler) from calling
apply_output_config again (infinite loop).
Rename enabled to enabling and use it exclusively for this purpose.
Rename configure to enabled, because that's what it really means.
[1]: https://github.com/swaywm/sway/pull/5521
Closes: https://github.com/swaywm/sway/issues/5483
The output manager config is created when the output is created. It is
updated when the mode, transform, scale, or layout for the output
changes, as well as, when the output is destroyed.
Since the output->enabled property was not being set before calling
apply_output_config, the output event handlers were early returning and
never updating the output manager config when the output state was
committed.
This fixes the issue by setting output->enabled in apply_output_config
below the output disabling section. There are also a few other minor
changes that are required to function.
Additionally, this renames output_enable to output_configure to better
describe the recent changes.
The only output_enable caller is now apply_output_config. Stop calling
apply_output_config from output_enable to simplify the code and avoid
the back-and-forth between these two functions.
output_enable is now the symmetric of output_disable: it just marks the
output as enabled and performs bookkeeping (e.g. creating teh default
workspace). It is called from apply_output_config after the output
commit, so that it can read the current output state and act
accordingly.
This change also allows us to avoid an extraneous wlr_output_commit.
References: https://github.com/swaywm/sway/issues/4921
Repaint scheduling delays output render and frame done events from
output frame events, and block idle frame events from being scheduled in
between output frame done and output render in this period of time.
If a surface is committed after its frame done event, but before output
render, idle frame requests will be blocked, and the surface relies on
the upcoming render to schedule a frame.
If when the repaint timer expires, output render is deemed unnecessary,
no frame will be scheduled. This can lead to surfaces never having their
frame callbacks fire.
To fix this, we store that a surface has requested a frame in
surface_needs_frame. When the repaint expires, if no render is deemed
necessary, we check this flag and schedule an idle frame.
Fixes#4768
Calling wlr_output_manager_v1_set_configuration with an enabled output
and a NULL mode is incorrect if the output doesn't support modes.
When DPMS'ing an output, wlr_output_enable(output, false) is called.
This de-allocates the CRTC and sets wlr_output.current_mode to NULL.
Because we mark DPMS'ed outputs as enabled, we also need to provide a
correct output mode. Add a field to sway_output to hold the current
mode.
Closes: https://github.com/swaywm/wlroots/issues/1867
The documentation for wayland-server.h says:
> Use of this header file is discouraged. Prefer including
> wayland-server-core.h instead, which does not include the server protocol
> header and as such only defines the library PI, excluding the deprecated API
> below.
Replacing wayland-server.h with wayland-server-core.h allows us to drop the
WL_HIDE_DEPRECATED declaration.
This commit si similar to wlroots' ca45f4490ccc ("Remove all wayland-server.h
includes").