Populate the wlr_output_state when setting a mode. This will allow
drm_connector_set_mode to stop relying on ephemeral fields in
wlr_drm_crtc. Also drm_connector_set_mode will be able to apply
both a new buffer and a new mode atomically.
When the session is inactive, we can't change the KMS state. Ignore
hotplug events so that compositors don't try to perform a modeset when
a connector is plugged in. We already re-scan connectors when the
session becomes active.
To test, run a wlroots compositor on VT 1, switch to VT 2, unplug a
connector, re-plug it, switch back to VT 1. Without this patch the
screen is black on VT 1.
References: https://github.com/swaywm/wlroots/issues/2370
This callback allowed compositors to customize the EGL config used by
the renderer. However with renderer v6 EGL configs aren't used anymore.
Instead, buffers are allocated via GBM and GL FBOs are rendered to. So
customizing the EGL config is a no-op.
Instead of operating on FDs in {open,close}_device, operate on
wlr_devices. This avoids the device lookup in wlr_session and allows
callers to have access to wlr_device fields.
For now, we use it to remove wlr_session_signal_add and replace it with
a more idiomatic wlr_session.events.change field. In the future, other
events will be added.
conn->crtc is NULL in case the output is disabled.
However, the DRM backend will set the GAMMA_LUT property anyway. On each
commit the whole state is sent to KMS. Adding WLR_DRM_CRTC_GAMMA_LUT to
the pending state would just make the backend re-create the blob
containing the gamma LUT.
This is a type which manages gbm_surfaces and imported dmabufs in the
same place, and makes the lifetime management between the two shared. It
should lead to easier to understand code, and fewer special cases.
This also contains a fair bit of refactoring to start using this new
type.
Co-authored-by: Simon Ser <contact@emersion.fr>
This fixes a segfault in drm_connector_set_mode (mode = NULL).
This happens because we set wlr_output.enabled to true if the connector
is attached to the CRTC. When the user disables an output in the
wlroots-based compositor, switches to another VT (enabling the output),
then switches back, wlroots sets wlr_output.enabled to true but
wlr_output.current_mode is NULL.
We should consider not reading properties from KMS after a TTY switch,
disabling all connectors. However this may result in flickering (outputs
being disabled then re-enabled).
Closes: https://github.com/swaywm/wlroots/issues/1874
This fixes a heap-use-after-free when the session is destroyed before
the backend during wl_display_destroy:
==1085==ERROR: AddressSanitizer: heap-use-after-free on address 0x614000000180 at pc 0x7f88e3590c2d bp 0x7ffdc4e33f90 sp 0x7ffdc4e33f80
READ of size 8 at 0x614000000180 thread T0
#0 0x7f88e3590c2c in find_device ../subprojects/wlroots/backend/session/session.c:192
#1 0x7f88e3590e85 in wlr_session_close_file ../subprojects/wlroots/backend/session/session.c:204
#2 0x7f88e357b80c in libinput_close_restricted ../subprojects/wlroots/backend/libinput/backend.c:24
#3 0x7f88e21af274 (/lib64/libinput.so.10+0x28274)
#4 0x7f88e21aff1d (/lib64/libinput.so.10+0x28f1d)
#5 0x7f88e219ddac (/lib64/libinput.so.10+0x16dac)
#6 0x7f88e21b415d in libinput_unref (/lib64/libinput.so.10+0x2d15d)
#7 0x7f88e357c9d6 in backend_destroy ../subprojects/wlroots/backend/libinput/backend.c:130
#8 0x7f88e3545a09 in wlr_backend_destroy ../subprojects/wlroots/backend/backend.c:50
#9 0x7f88e358981a in multi_backend_destroy ../subprojects/wlroots/backend/multi/backend.c:54
#10 0x7f88e358a059 in handle_display_destroy ../subprojects/wlroots/backend/multi/backend.c:107
#11 0x7f88e314acde (/lib64/libwayland-server.so.0+0x8cde)
#12 0x7f88e314b466 in wl_display_destroy (/lib64/libwayland-server.so.0+0x9466)
#13 0x559fefb52385 in main ../main.c:67
#14 0x7f88e2639152 in __libc_start_main (/lib64/libc.so.6+0x27152)
#15 0x559fefb4297d in _start (/home/simon/src/glider/build/glider+0x2297d)
0x614000000180 is located 320 bytes inside of 416-byte region [0x614000000040,0x6140000001e0)
freed by thread T0 here:
#0 0x7f88e3d0a6b0 in __interceptor_free /build/gcc/src/gcc/libsanitizer/asan/asan_malloc_linux.cc:122
#1 0x7f88e35b51fb in logind_session_destroy ../subprojects/wlroots/backend/session/logind.c:270
#2 0x7f88e35905a4 in wlr_session_destroy ../subprojects/wlroots/backend/session/session.c:156
#3 0x7f88e358f440 in handle_display_destroy ../subprojects/wlroots/backend/session/session.c:65
#4 0x7f88e314acde (/lib64/libwayland-server.so.0+0x8cde)
previously allocated by thread T0 here:
#0 0x7f88e3d0acd8 in __interceptor_calloc /build/gcc/src/gcc/libsanitizer/asan/asan_malloc_linux.cc:153
#1 0x7f88e35b911c in logind_session_create ../subprojects/wlroots/backend/session/logind.c:746
#2 0x7f88e358f6b4 in wlr_session_create ../subprojects/wlroots/backend/session/session.c:91
#3 0x559fefb51ea6 in main ../main.c:20
#4 0x7f88e2639152 in __libc_start_main (/lib64/libc.so.6+0x27152)
The documentation for wayland-server.h says:
> Use of this header file is discouraged. Prefer including
> wayland-server-core.h instead, which does not include the server protocol
> header and as such only defines the library PI, excluding the deprecated API
> below.
Replacing wayland-server.h with wayland-server-core.h allows us to drop the
WL_HIDE_DEPRECATED declaration.
On DRM resume, such as switching back to a TTY, the output needs to be
modeset to the current mode. However, wlr_output_set_mode will return
early when attempting to set the mode to the current mode. This just
steps around wlr_output_set_mode and calls drm_connector_set_mode
directly.
In order for a surface to be used as a cursor plane framebuffer, it
appears that requiring the buffer to be linear is sufficient.
GBM_BO_USE_SCANOUT is added in case GBM_BO_USE_LINEAR isn't sufficient
on untested hardware.
Fixes#1323
Removed wlr_drm_plane.cursor_bo as it does not serve any purpose
anymore.
Relevant analysis (taken from the PR description):
While trying to implement a fix for #1323, I found that when exporting
the rendered surface into a DMA-BUF and reimporting it with
`GBM_BO_USE_CURSOR`, the resulting object does not appear to be valid.
After some digging (turning on drm-kms debugging and switching to legacy
mode), I managed to extract the following error: ```
[drm:__setplane_check.isra.1 [drm]] Invalid pixel format AR24
little-endian (0x34325241), modifier 0x100000000000001 ``` The format
itself refers to ARGB8888 which is the same format as
`renderer->gbm_format` used in master to create the cursor bo. However,
using `gbm_bo_create` with `GBM_BO_USE_CURSOR` results in a modifier of
0. A modifier of zero represents a linear buffer while the modifier of
the surface that is rendered to is `I915_FORMAT_MOD_X_TILED` (see
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/include/uapi/drm/drm_fourcc.h?h=v4.20.6#n263).
In order to fix this mismatch in modifier, I added the
`GBM_BO_USE_LINEAR` to the render surface and everything started to work
just fine. I wondered however, whether the export and import is really
necessary. I then decided to test if the back buffer of the render
surface works as well, and at least on my hardware (Intel HD 530 and
Intel UHD 620) it does. This is the patch in this PR and this requires
no exporting and importing.
I have to note that I cheated in order to import DMA_BUFs into a cursor
bo when doing the first tests, since on import the Intel drivers check
that the cursor is 64x64. This is strange since cursor sizes other than
64x64 have been around for quite some time now
(https://lists.freedesktop.org/archives/mesa-commit/2014-June/050268.html).
Removing this check made everything work fine. I later (while writing
this PR) found out that `__DRI_IMAGE_USE_CURSOR` (to which
`GBM_BO_USE_CURSOR` translates) has been deprecated in mesa
(https://gitlab.freedesktop.org/mesa/mesa/blob/master/include/GL/internal/dri_interface.h#L1296),
which makes me wonder what the usecase of `GBM_BO_USE_CURSOR` is. The
reason we never encountered this is that when specifying
`GBM_BO_USE_WRITE`, a dumb buffer is created trough DRM and the usage
flag never reaches the Intel driver directly. The relevant code is in
https://gitlab.freedesktop.org/mesa/mesa/blob/master/src/gbm/backends/dri/gbm_dri.c#L1011-1089
. From this it seems that as long as the size, format and modifiers are
right, any surface can be used as a cursor.
Sessions can now be retrieved from a backend in a more general manner.
Multi-backend gets back its `session` field that contains the session
if one was created, removing the interfacing from multi backend with the
drm backend directly. This adds the possibility to use sessions even
without the drm backend.
It additionally fixes the bug that 2 session objects got created when
WLR_BACKENDS were set to "libinput,drm".
To allow vt switching without drm backend (and drm fd) on logind, start
listening to PropertiesChanged signals from dbus and parse the session
"Active" property when no master fd was created (this does not change
current drm backend behaviour in any way).
backend_get_renderer() is now returning the renderer of the primary GPU, instead
of its own renderer, since that's the thing which actually does all of the "real"
rendering
wlr_multi_backend_add() is now adding all subbackends (otherwise only one GPU
is handled).
credits: @ascent12
Compositors now have more control over how the backend creates its
renderer. Currently all backends create an EGL/GLES2 renderer, so
the necessary attributes for creating the context are passed to a
user-provided callback function. It is responsible for initializing
provided wlr_egl and to return a renderer. On fail, return 0.
Fixes#987
The current mode was set to NULL to abuse it as state variable
persisting DRM suspend/resume, this results resulted in a segfault on
normal DPMS cycle.
This reverts that change and uses the wlr_output enabled variable, which
also persists and makes more sense.
Simon Ser
Simon Zeni
Manuel Stoeckl
Scott Anderson
Brian Ashworth
Vincent Vanlaer
Drew DeVault
nyorain
Mariusz Bialonczyk
Ilia Bozhinov
Markus Ongyerth
Scott Anderson