The only output_enable caller is now apply_output_config. Stop calling
apply_output_config from output_enable to simplify the code and avoid
the back-and-forth between these two functions.
output_enable is now the symmetric of output_disable: it just marks the
output as enabled and performs bookkeeping (e.g. creating teh default
workspace). It is called from apply_output_config after the output
commit, so that it can read the current output state and act
accordingly.
This change also allows us to avoid an extraneous wlr_output_commit.
References: https://github.com/swaywm/sway/issues/4921
If applying an output config to an output fails, the output may be
destroyed. To be able to handle this situation correctly,
apply_output_config_to_outputs needs to use wl_list_for_each_safe.
When an input becomes available, the input type config for that device
type will be merged underneath the input identifier config, provided
they both exist. If an input type config gets added or modified at a
later point, then those changes get merged onto the input identifier
configs for that type. However there was a missing case of the input
identifier config being added after the device is already available and
the input type config existing. This makes it so that the first time an
input identifier config gets stored, there will be a check to see if it
matched any of the available devices. If it does, then there will be a
search for the associated input type config, which will be merged
underneath the input identifier config if found.
This adds seat configuration options which can be used to configure what
events affect the idle behavior of sway.
An example use-case is mobile devices: you would remove touch from the
list of idle_wake events. This allows the phone to stay on while you're
actively using it, but doesn't wake from idle on touch events while it's
sleeping in your pocket.
A wlr_keyboard_group allows for multiple keyboard devices to be
combined into one logical keyboard. This is useful for keyboards that
are split into multiple input devices despite appearing as one physical
keyboard in the user's mind.
This adds support for wlr_keyboard_groups to sway. There are two
keyboard groupings currently supported, which can be set on a per-seat
basis. The first keyboard grouping is none, which disables all grouping
and provides no functional change. The second is keymap, which groups
the keyboard devices in the seat by their keymap. With this grouping,
the effective layout and repeat info is also synced across keyboard
devices in the seat. Device specific bindings will still be executed as
normal, but everything else related to key and modifier events will be
handled by the keyboard group's keyboard.
set_cloexec is defined by both sway and wlroots (and who-knows-else),
so rename the sway one for supporting static linkage. We also remove
the duplicate version of this in client/.
Fixes: https://github.com/swaywm/sway/issues/4677
Calling wlr_output_manager_v1_set_configuration with an enabled output
and a NULL mode is incorrect if the output doesn't support modes.
When DPMS'ing an output, wlr_output_enable(output, false) is called.
This de-allocates the CRTC and sets wlr_output.current_mode to NULL.
Because we mark DPMS'ed outputs as enabled, we also need to provide a
correct output mode. Add a field to sway_output to hold the current
mode.
Closes: https://github.com/swaywm/wlroots/issues/1867
When applying config, value mode->refresh is mHz; convert it to Hz before
assigning it to the temporary output config. oc->refresh_rate will
be converted back to mHz in set_mode function.
Fix debug log printing GHz instead of Hz.
This adds complete support for the barconfig_update ipc event. This also
changes the bar command and subcommand handlers to correctly emit the
event. This makes it so all bar subcommands other than id and
swaybar_command are dynamically changeable at runtime. sway-bar.5 has
been updated accordingly
When applying an output config, an output may transform or be altered
in some way that effects the cursor. In order for the cursor images to
be updated properly, all cursors need to be rebased after applying
output configs.
Adds a new commend "xkb_file", which constructs the internal
xkb_keymap from a xkb file rather than an RMLVO configuration.
This allows greater flexibility when specifying xkb configurations.
An xkb file can be dumped with the xkbcomp program.
In apply_output_config, this sets output->{width,height} using the
values in the output box. Previously, they were being set using
wlr_output_transformed_resolution, which takes the width and height
from the wlr_output and just checks whether they should be swapped
based on the transform. This did not take into account the output's
scale. wlr_output_effective_resolution could be used instead, which
handles both transform and scale. However, the values in the output box
have already been processed by wlr_output_effective_resolution so they
can just be used directly
This allows for an optional validation stage when storing an input
config. Currently, only the xkb keymap is validated. If storing the
delta input config will result in any invalid xkb keymaps, the input
config will not be stored and error will be populated with the first
line of the xkbcommon log.
New 'seat <name> xcursor_theme <theme> [<size>]' command that
configures the default xcursor theme.
The default seat's xcursor theme is also propagated to XWayland, and
exported through the XCURSOR_THEME and XCURSOR_SIZE environment
variables. This is done every time the default seat's configuration is
changed.
This fixes a typo in `merge_id_on_name` for output configs that
resulted in incorrect id-on-name output configs being generated.
Instead of using the output that matched the name or identifier, the
first output in the list was being used instead. This could cause
merging across unrelated output configs and preventing output configs
from being applied correctly
When reloading, this destroys the old config's swaybg client before
spawning the new config's swaybg. This fixes a race condition where the
old config's swaybg client's destroy was being called after the new
config's swaybg client was being spawned. This was causing the
reference to the new swaybg client to be removed and never destroyed.
This also modifies handle_swaybg_client_destroy to grab the config
reference using wl_container_of on the listener since the swaybg client
may be the old config swaybg client and should be used instead of the
global config instance
Add support for configurations that apply to a type of inputs
(i.e. natural scrolling on all touchpads). A type config is
differentiated by a `type:` prefix followed by the type it
corresponds to.
When new devices appear, the device config is merged on top of its
type config (if it exists). New type configs are applied on top of
existing configs.
This makes it so there will only be one swaybg instance running
instead of one per output. swaybg's cli has been changed to a xrandr
like interface, where you select an output and then change properties
for that output and then select another output and repeat. This also
makes it so swaybg is only killed and respawned when a background
changes or when reloading.
Many laptop screens report unknown subpixel order. Allow users to manually set subpixel hinting to work around this.
Addresses https://github.com/swaywm/sway/issues/3163
In #3916, I overlooked that `get_output_config` does not handle
wildcards unless the config is reloading, which is a remnant of older
iterations of the output config handling that went unnoticed due to
`output_find_config` handling it. With the current version of the
output config handling, having `get_output_config` handle wildcard
configs is actually preferable. This fixes having only a wildcard
output config in the config file or when connecting/enabling a new
output with only a wildcard config existing.
This revamps the way that output configs are handled when referencing
an output by both identifier and name. If an output is always referred
to by name or by identifier, this should have no noticeable change. As
soon as there is a name output config and an identifier output config
that matches an output, an output config is generated that is named
`<identifier> on <name>` that is generated with the identifier output
config merged on top of the name output config and stored. When a
change to either is stored, the delta is merged on top of that
"id on name" output config, as well. If the "id on name" output config
exists, it has the highest precedence and will be used when applying
a config to the output.
This fixes the following case:
- `swaymsg output <name> bg /path/to/wallpaper1 fill`
- `swaymsg output <identifier> bg /path/to/wallpaper2 fill`
- `swaymsg output <name> dpms on`
Without this, the wallpaper is changed to `/path/to/wallpaper1`. With
this, the wallpaper remains `/path/to/wallpaper2`.
This removes `output_find_config`, which would take the first matching
output config it found. This is fine if only a name output config,
identifier output config, or even just wildcard exist, but if there is
a name output config and identifier output config, they are not merged.
Instead, this introduces find_output_config, which is just a wrapper
for `get_output_config`. This ensures that both the name and identifier
output configs are respected.
This fixes the following case:
- For simplicity in this example, remove all output configs from config
- Run `swaymsg output <name> bg #ff0000 solid_color`
- Run `swaymsg output <identifier> scale 2`
- Disconnect and reconnect output
Without this, the output will have the background, but not the scale.
With this, the output will have both the background and scale
This fixes the issue of the display freezing on reload with
wlroots#1545.
On master, all output configs are applied on reload. This may cause an
output to have its config applied up to three times, instead of just
once. The three cases are: output name, output identifier, and wildcard.
Not only is this inefficient, but it can cause swaybg to be spawned and
immediately killed.
However, swaybg requires two roundtrips of wl_display (to obtain needed
globals) before it enters its normal event loop. Modesetting will
roundtrip the wl_display. Without modesetting, waitpid for killing
swaybg could block infinitely due to swaybg being blocked by
wl_display_roundtrip.
This only configured an output once. It either uses the wildcard config
or creates an empty wildcard config and applies that. This also fixes a
bug where an output would not be reset when there is no output config to
apply to it.
On the DRM backend, if an output is dpms'd off and a different output is
hotplugged, the CRTC for the output is reclaimed. When modesetting an
output without a CRTC, a CRTC will not be given to an output that is not
desired to be enabled. This splits setting the dpms state in
apply_output_config. If the output should be dpms on, the it is enabled
before attempting to modeset. Otherwise, it is dpms'd off after setting
everything else.
This also adds DPMS_ON to the default output configs.
This fixes a few misc memory leaks reported by asan:
- Items of `config->config_chain` are now freed instead of just the list
itself
- `bar->swaybar_command` is now freed
- The result returned by a seat subcommand is now returned instead of
leaked
This changes the `pointer_constraint` command to be a subcommand of seat
to allow for per-seat settings. The current implementation that is not a
seat subcommand will only operate on the current seat and will segfault
in the config due to `config->handler_context.seat` only being set at
runtime.
This also allows for the wildcard identifier to be used to alter the
pointer constraint settings on all seats and allows for the setting to
be merged with the rest of the seat config.
Modifier handling functions were moved into sway/input/keyboard.c;
opposite_direction for enum wlr_direction into sway/tree/output.c;
and get_parent_pid into sway/tree/root.c .
This commit mostly duplicates the wlr_log functions, although
with a sway_* prefix. (This is very similar to PR #2009.)
However, the logging function no longer needs to be replaceable,
so sway_log_init's second argument is used to set the exit
callback for sway_abort.
wlr_log_init is still invoked in sway/main.c
This commit makes it easier to remove the wlroots dependency for
the helper programs swaymsg, swaybg, swaybar, and swaynag.
This happens if you plug in more outputs than supported by your GPU.
This patch makes it so outputs without CRTCs appear as disabled. As soon as
they get a CRTC (signalled via the mode event), we can enable them.
This modifies `bar_cmd_tray_bindsym` to use `get_mouse_bindsym` for
parsing mouse buttons. This also introduces `bar_cmd_tray_bindcode`,
which will use `get_mouse_bindcode` for parsing mouse buttons. Like with
sway bindings, the two commands are encapsulated in a single file to
maximize shared code.
This also modifies tray bindings to work off of events codes rather than
x11 buttons, which allows for any mouse buttons to be used.
For `get_bar_config`, `event_code` has been added to the `tray_bindings`
section and will include to event code for the button. If the event code
can be mapped to a x11 button, `input_code` will still be the x11 button
number. Otherwise, `input_code` will be `0`.
Adds the bar subcommand `status_padding <padding>` which allows setting
the padding used for swaybar. If `status_padding` is set to `0`, blocks
will be able to take up the full height of the bar.
This makes seat configs work like output and input configs do. This also
adds support for wildcard seat configs. A seat config is still created
in the main seat command handler, but instead of creating a new one in
the subcommands and destroying the main seat command's instance, the
seat subcommands modify the main one. The seat config is then stored,
where it is merged appropriately. The seat config returned from
`store_seat_config` is then applied. When attempting to apply a wildcard
seat config, a seat specific config is queried for and if found, that is
used. Otherwise, the wildcard config is applied directly.
Additionally, instead of adding input devices to the default seat
directly when there is no seat configs, a seat config for the default
seat is created with only fallback set to true, which is more explicit.
It also fixes an issue where running a seat command at runtime (with no
seat config in the sway config), would result in all input devices being
removed from the default seat and leaving sway in an unusable state.
Also, instead of checking for any seat config, the search is for a seat
config with a fallback option seat. This makes it so if there are only
seat configs with fallback set to -1, the default seat is still created
since there is no explicit notion on what to do regarding fallbacks.
However, if there is even a single fallback 0, then the default seat is
not used as a fallback. This will be needed for seat subcommands like
hide_cursor where the user may only want to set that property without
effecting anything else.
Moves the call to `terminate_swaybg` from inside `apply_output_config` to
`output_disable`. The former was only called when an output was being
disabled. The latter is called when an output is being disabled and when
an output becomes disconnected. Without this, disconnecting an enabled
output would result in a defunct swaybg process.
Default output configs were generated on reload to reset an output to
its default settings. The idea was that anything that was removed from
the config or changed at runtime and not in the config should be reset
on reload. Originally, they were created using the output name. Recently,
they were changed to use the output identifier. It turns out that there
are issues of shadowing with that solution as well. This should fix
those issues.
Instead of generating the default output configs on reload and storing
them in the output config list to merge on top of, they are now only
generated when retrieving the output config for an output during a
reload. This means that the default output configs are never stored
anywhere and just used as a base to merge unaltered user configs on top
of during a reload.
Starting with a blank output config, merges get applied in the following
order:
1. Default output config (only during a reload)
2. Wildcard config (only if neither output name or output identifier
exist)
3. Output name config
4. Output identifier config
When generating default output configs to reset the outputs to their
default settings on reload, the output name was being used.
Additionally when determining the output config to apply, if there was
an output config with the output name, that was being used without
checking for an identifier config. This caused sway to completely ignore
the users specified output config.
To fix this issue, the following changes have been made:
1. Default output configs as created for the identifier now instead of
name. This actually makes more sense anyway since you could hotplug
multiple different outputs to the same port.
2. In get_output_config, which is only used to determine which output
config to apply, output configs for both the name and identifier are
queried. If both are found, a new output config is generated with the
identifier config merged on top of the name config. If just one is found,
a copy of that config is returned. This change also requires that the
result from get_output_config be freed after use to prevent memory
leaks, which required some minor changes to logic in
apply_output_config_to_outputs.
Since wayland does not currently allow swaybar to create global
keybinds, this is handled within sway and sent to the bar using a custom
event, so as not to pollute existing events, called bar_state_update.
Sway sets a default status_command which runs date every second. This
patch removes this behaviour so the user can have a NULL status bar if
desired.
I had to swap swaybar's event_loop_poll and wl_display_flush so that it
would map the initial surface.
This changes it back so the path given to swaybg is enclosed in quotes.
Additionally, the only character that is escaped in the path stored is
double quotes now. This makes it so we don't need to keep an exhaustive
list of characters that need to be escaped.
The end user will still need to escape these characters in their config
or when passed to swaybg.
Simon Ser
Brian Ashworth
Paul Riou
Ronan Pigott
Drew DeVault
Ivan Molodetskikh
Tadeo Kondrak
Sheena Artrip
lbonn
Danilo Spinella
Rouven Czerwinski
Antonin Décimo
Ed Younis
Sergei Dolgov
Daniel Eklöf
Konstantin Pospelov
Benjamin Cheng
Jan Beich
Geoff Greer
Noam Preil
Connor E
Ryan Dwyer
M Stoeckl
Ian Fan
Spencer Michaels
Arkadiusz Hiler
PP