The following situation can be dangerous:
- Output DP-1 is plugged in, compositor enables it.
- User VT switches away.
- User unplugs DP-1.
- User VT switches back.
- scan_drm_connectors() figures out the output is now disconnected,
uninitializes the struct wlr_output.
- The loop restoring previous output state in handle_session_active()
accesses the struct wlr_output to figure out what to restore.
By chance, we zero out the struct wlr_output after uninitializing it,
so enabled and current_mode will always be zero. But let's make sure
we handle this case explicitly, to remind future readers that it exists
and make the code less fragile.
The old drm_connector_set_mode() function did that by calling
drm_crtc_page_flip(). We lost this in the refactoring.
Fixes: f216e97983 ("backend/drm: drop drm_connector_set_mode()")
Once we are DRM master, the CRTC cannot be changed behind our back
except during a VT switch.
After a VT switch, we try to restore whatever KMS state we had last
programmed. Reloading the current CRTC from KMS breaks this and
can result in a modeset without a FB.
Closes: https://gitlab.freedesktop.org/wlroots/wlroots/-/issues/3432
The drm_connector_commit_state() call in handle_session_active()
was not resulting in any atomic commit, because it didn't match any
of the if branches: active = true, no new buffer was committed,
and adaptive sync/gamma LUT were unchanged. Thus the commit was a
no-op.
Later on, when the compositor performs regular page-flips, the
kernel would return EINVAL indicating that a modeset was needed.
Rework the logic to use a non-blocking page-flip commit if a buffer
was committed, and use a blocking commit if the connector is on or
is being disabled. The only case where we should skip the atomic
commit is when disabling (active = false) an already-disabled
connector (conn->crtc == NULL).
Note, 6936e163b5 ("backend/drm: short-circuit no-op commits")
has introduced early returns for other situations where we don't
need to perform an atomic commit (e.g. updating scale or transform
of an output).
Fixes: f216e97983 ("backend/drm: drop drm_connector_set_mode()")
Closes: https://gitlab.freedesktop.org/wlroots/wlroots/-/issues/3432
Extract the logic to fetch the current mode to a separate function
to make it more readable. Stop dying in an assert when
get_drm_prop_blob() fails. Always make it so the drmModeModeInfo
pointer is allocated so that we can free() it unconditionally.
We already have disconnect_drm_connector() to handle the
CONNECTED → DISCONNECTED transition. Let's add
connect_drm_connector() to handle DISCONNECTED → CONNECTED. This
makes scan_drm_connectors() shorter and easier to follow.
No functional change, literally just moving code around.
We were using the legacy API (with a detour through drmModeEncoder)
to find out the current CRTC for a connector. Use the atomic API
when available.
Also extract the whole logic into a separate function for better
readability, and better handle errors.
Instead of special-casing modesets, we can just cut the wrapper
and directly call drm_crtc_page_flip(). drm_connector_test() should
already have the checks previously done in drm_connector_set_mode(),
all we need to do is update enabled/mode after a successful atomic
commit.
This field becomes stale too easily: for instance, see 6adca4089c
("backend/drm: don't unconditionally set desired_enabled").
Additionally, drm_connector_alloc_crtc() needs to do some weird
dance, restoring its previous value.
Instead, add a connector arg to realloc_crtcs() to indicate a new
connector we want to enable.
We were unconditonally setting desired_enabled = true for all
connected connectors. This makes realloc_crtcs() always keep a CRTC
active for these, even if the user doesn't want to enable them.
When starting up, the compositor might call wlr_output_set_mode()
with a mode which is already the current one. wlroots will detect
this and make the wlr_output_set_mode() call a no-op. During the
next wlr_output_commit() call, wlroots will perform an atomic
commit without the ALLOW_MODESET flag.
This is an issue, because some drivers need ALLOW_MODESET even if
the mode is the same. For instance, if the FB stride or modifier
changed, some drivers require a modeset.
Add a new flag "allow_artifacts" which is set when the compositor
calls mode-setting functions. Use this flag to figure out whether
we want to perform atomic commits with ALLOW_MODESET.
(The name "allow_artifacts" is picked because ALLOW_MODESET is a
misnomer, see [1].)
[1]: https://patchwork.freedesktop.org/patch/505107/
Closes: https://gitlab.freedesktop.org/wlroots/wlroots/-/issues/3499
Previously, adaptive sync was just a hint and wouldn't make any
atomic commit fail if the backend didn't support it. The main reason
is wlr_output_test wasn't supported at the time.
Now that we have a way for compositors to test whether a change can
work, let's remove the exception for adaptive sync and convert it to
a regular output state field.
"max bpc" is a maximum value, the driver is free to choose a
smaller value depending on the bandwidth available.
Some faulty monitors misbehave with higher bpc values. We'll add
a workaround if users get hit by these in practice.
References: https://gitlab.freedesktop.org/wayland/weston/-/issues/612
The EDID 1.4 spec says that the serial number is optional:
> If this field is not used, then enter “00h, 00h, 00h, 00h”.
Leave the wlr_output.serial field NULL in that case, and hide it
from the output description.
CTA-861-G says that "graphics" is used to indicate non-analog (ie,
digital) content. With that bit set, the sink should turn off analog
reconstruction and other related filtering.
Some output commits (changing e.g. the output scale or transform)
don't require any change in the KMS state. Instead of going through
a KMS commit, return early. Blocking KMS commits can be expensive.
The wlr_output API requires compositors to wait for wlr_output.frame
before submitting a new buffer. However, compositors can perform a
commit which doesn't involve a buffer anytime.
If the commit is a modeset, we set DRM_MODE_ATOMIC_ALLOW_MODESET and
block until the commit is done. If it isn't, we currently always
perform a non-blocking commit. This is an issue because a previous
page-flip might still be in flight kernel-side, returning EBUSY.
Fix this by using blocking commits when a buffer isn't submitted by
the compositor.
Closes: https://github.com/swaywm/sway/issues/6962
References: https://gitlab.freedesktop.org/wlroots/wlroots/-/issues/2239
Simon Ser
illiliti
Alexander Orzechowski
Simon Zeni
vanfanel
Isaac Freund