This commit changes how commands decide what container to act on.
Commands get the current container though `current_container`, a global
defined in sway/commands.c. If a criteria is given before a command,
then the following command will be run once for every container the
criteria matches with a reference to the matching container in
'current_container'. Commands should use this instead of
`get_focused_container()` from now on.
This commit also fixes a few (minor) mistakes made in implementing marks
such as non-escaped arrows in sway(5) and calling the "mark" command
"floating" by accident. It also cleans up `criteria.c` in a few places.
This commit adds three commands to sway: `show_marks`, `mark` and
`unmark`. Marks are displayed right-aligned in the window border as i3
does. Marks may be found using criteria.
Fixes#1007
Some users may want to switch buttons on their input devices, turns out
libinput already supports it. Let's add a support for it in our config.
Signed-off-by: Michał Winiarski <knr@hardline.pl>
Fixes#819. If workspace is focused and command 'move container to
workspace/output' is issued, workspace child containers are wrapped in a
new container and moved according to command.
When workspace_auto_back_and_forth is enabled, workspaces get switched
twice with previously mentioned command, which is not the expected
behavior.
Removes one redundant creation of previous workspace.
Replace `update_view_border()` with `update_container_border()`. The latter
should handle both the case where the container is a view or if the container
has children.
Deeply nested containers which had their layouts changed didn't update
their actual_geometry, this messed up their child containers. Those got
width and height of 0, which was then decreased for stacked/tabbed
containers by title height. Underflow ensued, these containers suddenly
had height 4294967273. In short, not updating actual_geometry didn't
play nicely with nested containers.
Previously, cmd_kill only closed a focused view, while containers were
not affected. Now it closes all views that are children of the focused
container.
Tabbed/stacked containers are now created only if a view is present on
the workspace. If a view is created on previously empty tabbed/stacked
workspace, it gets wrapped in a container.
Values cannot be negative or 0; if so uses the default 75x50.
Uses the same syntax as i3: floating_minimum_size <width> x <height>, although the x can be anything.
when creating a new output, move to that output all extant workspaces
that are assigned to that output.
(unrelated) remove comment that was no longer applicable, fix spacing in
an assignment
The borders are implemented as a surface/buffer attached to each view
which is sent to and rendered by wlc in the view_pre_render callback.
All the drawing logic is handled in sway/border.c and all the logic for
calculating the geometry of the border/view is handled in
`update_geometry` in sway/layout.c (same place as gaps are calculated).
The include command (`include <path>`) makes it possible to include sub
config files from the main config file (or from within other sub config
files).
The include command uses the following rules for including config files:
* the `path` can be either a full path or a path that is relative to the
parent config. Shell expansion is supported, so it's possible to do
`include ~/.config/sway.d/*`.
* The same config file can only be included once (to prevent include
cycles). If a config is included multiple times it will just be
ignored after it has been included once.
* Including a sub config file is the same as inserting the content of
that file into the parent config, thus rules about overwriting
bindsyms etc. works the same as for a single config.
Implement #542
Calvin Lee
Zandr Martin
Drew DeVault
D.B
Michał Winiarski
Guillaume Brogi
Tony Crisci
Drew DeVault
Mykyta Holubakha
David Eklov
Zandr Martin
Zandr Martin
Denis Doria
Mikkel Oscar Lyderik
Raman Varabets
Eric Engestrom
Jasen Borisov
Daniel Lockyer
Kevin Hamacher