This modifies `seat_cmd_cursor` to utilize `get_mouse_button` when
parsing mouse buttons for the `press` and `release` operations. All x11
buttons, button event names, and button event codes are supported.
For x11 axis buttons, `dispatch_cursor_axis` is used instead of
`dispatch_cursor_button`. However the `press`/`release` state is ignored
and the either axis event is processed. This also removes support for
`left` and `right` in favor of `BTN_LEFT` and `BTN_RIGHT`.
This modifies `bindcode` and `bindsym` to use `get_mouse_bindcode` and
`get_mouse_bindsym`, respectively, to parse mouse buttons. Additionally,
the `BINDING_MOUSE` type has been split into `BINDING_MOUSECODE` and
`BINDING_MOUSESYM` to match keys and allow for mouse bindcodes to be
used. Between the two commands, all button syms and codes should be
supported, including x11 axis buttons.
Implements `tiling_drag_threshold <threshold>` to prevent accidental
dragging of tiling containers. If a container (and all of its
descendants) are unfocused and the tile bar is pressed, a threshold
will be used before actually starting the drag. Once the threshold has
been exceeded, the cursor will change to the grab icon and the operation
will switch from `OP_MOVE_TILING_THRESHOLD` to `OP_MOVE_TILING`.
This modifies the way mouse bindings are parsed. Instead of adding to
BTN_LEFT, which results in button numbers that may not be expected,
buttons will be parsed in one of the following ways:
1. `button[1-9]` will now map to their x11 equivalents. This is already
the case for bar bindings. This adds support for binding to axis events,
which was not possible in the previous approach.
2. Anything that starts with `BTN_` will be parsed as an event code name
using `libevdev_event_code_from_name`. This allows for any button to be
mapped to instead of limiting usage to the ones near BTN_LEFT. This also
adds a dependency on libevdev, but since libevdev is already a dependency
of libinput, this should be fine. If needed, this option can have dependency
guards added.
Binding changes:
- button1: BTN_LEFT -> BTN_LEFT
- button2: BTN_RIGHT -> BTN_MIDDLE
- button3: BTN_MIDDLE -> BTN_RIGHT
- button4: BTN_SIDE -> SWAY_SCROLL_UP
- button5: BTN_EXTRA -> SWAY_SCROLL_DOWN
- button6: BTN_FORWARD -> SWAY_SCROLL_LEFT
- button7: BTN_BACK -> SWAY_SCROLL_RIGHT
- button8: BTN_TASK -> BTN_SIDE
- button9: BTN_JOYSTICK -> BTN_EXTRA
Since the axis events need to be mapped to an event code, this uses the
following mappings to avoid any conflicts:
- SWAY_SCROLL_UP: KEY_MAX + 1
- SWAY_SCROLL_DOWN: KEY_MAX + 2
- SWAY_SCROLL_LEFT: KEY_MAX + 3
- SWAY_SCROLL_RIGHT: KEY_MAX + 4
This adds support for `i3 4.16`'s ability to set the title alignment.
The command is `title_align left|center|right`.
When the title is on the right, marks are moved to the left. Otherwise,
they are on the right.
`i3 4.16` allows users to list multiple outputs for a workspace and the
first available will be used. The syntax is as follows:
`workspace <workspace> output <outputs...>`
Additionally when the workspace is created, the outputs get added to the
output priority list in the order specified. This ensures that if a higher
output gets connected, the workspace will move to the higher output. This
works the same way as if the user had a workspace on an output, disconnected
the output, and then later reconnected the output.
This implements the following syntaxes from `i3 4.16`:
* `resize set [width] <width> [px|ppt]`
* `resize set height <height> [px|ppt]`
* `resize set [width] <width> [px|ppt] [height] <height> [px|ppt]`
Additionally, a bug was fixed that caused setting the height of a tiled
container to change the width instead due to a typo.
This introduces the following command extensions from `i3-gaps`:
* `gaps horizontal|vertical|top|right|bottom|left <amount>`
* `gaps horizontal|vertical|top|right|bottom|left all|current
set|plus|minus <amount>`
* `workspace <ws> gaps horizontal|vertical|top|right|bottom|left
<amount>`
`inner` and `outer` are also still available as options for all three
of the above commands. `outer` now acts as a shorthand to set/alter
all sides.
Additionally, this fixes two bugs with the prevention of invalid gap
configurations for workspace configs:
1. If outer gaps were not set and inner gaps were, the outer gaps
would be snapped to the negation of the inner gaps due to `INT_MIN`
being less than the negation. This took precedence over the default
outer gaps.
2. Similarly, if inner gaps were not set and outer gaps were, inner
gaps would be set to zero, which would take precedence over the
default inner gaps.
Fixing both of the above items also requires checking the gaps again
when creating a workspace since the default outer gaps can be smaller
than the negation of the workspace specific inner gaps.
The directive controlled whether floating views should raise to the top
when the cursor is moved over it while using focus_follows_mouse. The
default was enabled, which is undesirable. For example, if you have two
floating views where one completely covers the other, the smaller one
would be inaccessible because moving the mouse over the bigger one would
raise it above the smaller one.
There is no known use case for having raise_floating enabled, so this
patch removes the directive and implements the raise_floating disabled
behaviour instead.
While allowing negative values for the outer gaps it is still prevented that negative values move windows out of the container. This replaces the non-i3 option for edge_gaps.
This introduces a new view_impl function: is_transient_for. Similar to
container_has_ancestor but works using the surface parents rather than
the tree.
This patch modifies view_is_visible, container_at and so on to allow
transient views to function normally when they're in front of a
fullscreen view.
Fixes `hide_edge_borders smart` when gaps are in use.
Implements `hide_edge_borders smart_no_gaps` and `smart_borders
on|no_gaps|off`.
Since `smart_borders on` is equivalent to `hide_edge_borders smart`
and `smart_borders no_gaps` is equivalent to `hide_edge_borders
smart_no_gaps`, I opted to just save the last value set for
`hide_edge_borders` and restore that on `smart_borders off`. This
simplifies the conditions for setting the border.
Drew DeVault
Ryan Dwyer
Brian Ashworth
David96
Alex Maese
mwenzkowski
Florent de Lamotte
emersion
Connor E
madblobfish
Tom Warnke
mteyssier
Ian Fan
Tarmack
chtison
Rouven Czerwinski
Brian Ashworth
Jonathan Buch